ASTM A285 is a type of ordinary carbon steel intended for fusion-welded pressure vessel equipments as boiler, storage tank, heat exchangers, etc. With 3 steel grades (Grade A, Grade B, Grade C) covering tensile strength range from 310-515Mpa,usually ASTM A285 steel plate is delivered as-rolled condition. made by killed, semi-killed, capped or EN 10224 Grade L235 Carbon Steel Seamless Tubes EN 10224 Grade L235 Specification. EN 10224 Grade L235 Carbon Steel Seamless Tubes are also known as mild steel pipes and tubes.EN 10224 Grade L235 Tubes are low-cost Low Carbon Steel Tubes with max 017 % carbon content with combination of max 080 % manganese easy to form and shape .These pipes are manufactured as per EN Specification and commercially referred as cs pipes
FerroPipE is considered as the most Reliable EN 10224 Grade L235 Tubes Supplier from India. EN 10224 Grade L235 Carbon Steel Seamless Tubes are certified with Mill test Certificate in accordance with En 10204 Type 3.1/3.2. Where 3.2 indicates In-stage inspection by independent inspection agencies like TUV, DNV, BVQS, LLOYDS & EIL. Equivalents of Carbon Steel QualitiesHigh Yield Steel High yield strength cold forming steels Simple pressure vessels steel Stamping and cold forming steels Steel for Boilers and Pressure Vessels Steel for gas cylinders and gas vessels Steel for large diameter pipes Steel For Ship Building:Steel for welded tubes Steel Resistant to Atmospherical corrossion Steel with Cr., Mo.,Cr-Mo. Grade SpecificationsMartensitic Stainless Steel:PH Type Stainless Steel:Cast Iron:587XRm:C1-C2:M30-M20 K40-K20: Carbon Steel:Stainless Steel:Non Ferrous:Conditional use in Cast Iron:LT-2373B:C1-C3:K25-K15 LTC-235:C2-C3:K10-K30 H30-H35:High content CBN,
Olympic Steel boasts a broad range of hot rolled coil, sheet and plate steel products and grades in inventory; in both Hot Roll dry and Pickled and Oiled (P&O), automotive grades, Advanced High Strength Steels (AHSS), High Strength Low Alloys (HSLA) in both ASTM and AISI standards, as well as branded products COR-TEN®, DOMEX , EX-TEN®, FREMAX® steel products and more. Material Data Sheets for the Construction of Piping Product Carbon steel Type 235 1) Carbon steel Type 235LT impact tested Carbon steel Type 360LT impact tested Stainless steel Type 316 Stainless steel Type 22Cr Duplex Stainless steel Type 25Cr Duplex Stainless steel Type 6Mo2) Cu/Ni 90/10 and other copper alloys Nickel alloy ium Grade 2 3) High strength low alloyed PRODUCT GUIDES - Central Steel & Wire Co. Typical hardness range of 185-235 Brinell Used for sliding-type abrasion ALLOY ASTM A 514 aka T1* 1/4 - 2-1/2 100 110 90° 2 t transverse Do not pickle destroys properties shot blast -Carbon and HSLA steel with specified minimum yield thru 80,000 psi.
Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S235JR Round Bar S235JR Flat Bar S235JR Hollow Bar S235JR Tube / Pipe S235JR Sheet / Plate S235JR Strip / Coil S235JR Wire S235JR Forging S235JR Tube / Pipe TEL:+86-80247006 S235JR steel - Steel GradesTool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S235JR Round Bar S235JR Flat Bar S235JR Hollow Bar S235JR Tube / Pipe S235JR Sheet / Plate S235JR Strip / Coil S235JR Wire S235JR Forging S235JR Tube / Pipe TEL:+86-80247006 Steel Material Types - DefinitionsA53 = A53 is carbon steel pipe which encompasses both seamless and welded carbon steel and dipped galvanized steel pipe. A53 pipe is used for pressure and mechanical applications where steam, water, gas and air are incorporated. It is formable and weldable in all applications. A53 pipe comes in three types (F, E, and S) and two grades (A and B).
Structural grade carbon steel acc. DIN EN 10025-2:2004 with the grades S235JR, S235J0, S235J2, S275JR, S275J0, S275J2, S335JR, S335J0 und S355K2. Table of material properties for structural steel S235 The unit weight of structural steel is specified in the design standard EN 1991-1-1 Table A.4 between 77.0 kN/m 3 and 78.5 kN/m 3. For structural design it is standard practice to consider the unit weight of structural steel equal to = 78.5 kN/m 3 and the density of structural steel approximately = 7850 kg/m 3. Modulus of elasticity of Tensile / Yield Strength of Steel Charttensile - yield strength of steel chart Tensile / yield strengths and ductilities for some of the plain carbon and low alloy steels are given in the following mechanical properties of steel chart. Yield Strength, Tensile Strength and Ductility Values for Steels at Room Temperature
S235JR carbon steel plate is the European standard of non-alloy structural steels, equivalent to GB Q235B steel paltes, namely carbon structural steels with low carbon, used for welding, bolting, and more riveted structure. S235 steel - Steel GradesS235 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.